3 in stock (can be backordered)

- +



STM32F722, MPU6000, OSD, DPS310, 32M Flash, 5x UARTs, 8x DShot, 2~8S, BEC 5V2A, VTX power switch, Dual Camera image switch. convertible 20mm to 30.5mm mounting.

The Matek F722-Minsi SE has been improved of the previous NON SE version and now has a BMP280 Barometer.

Matek F722-MINI(SE)
Matek F722-MINI(SE)












Matek F722-mini(SE)
Matek F722-mini(SE)





























F722-miniSE Quick Start Guide

FC Specifications

  • MCU: 216MHz STM32F722RET6
  • IMU: MPU6000 (SPI)
  • OSD: AT7456E (SPI)
  • Baro: Infineon DPS310 (I2C)
  • Blackbox: 32M-byte Flash memory (SPI)
  • 5x Uarts (1,2,3,4,6) with build-in inversion
  • 1x Softserial supported
  • 8x Dshot/Proshot/oneshot outputs
  • 1x I2C
  • 1x SH1.0_8pin connector (Vbat/G/Curr/R6/S1/S2/S3/S4)
  • 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
  • Vbat filtered output power for VTX,  Switchable via AUX (modes tab-user1)
  • Dual Camera image switchable via AUX (modes tab-user2)
  • Convertible 20mm to 30.5mm mounting
  • Camera control: Yes
  • Smartaudio & Tramp VTX protocol: Yes
  • DJI OSD: Yes (any spare Uart Tx & Rx)
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes
  • Additional ADC for INAV analog airspeed


  • Input: 6~36V (2~8S LiPo)
  • BEC: 5V 2A
  • LDO 3.3V: Max.200mA
  • Battery Voltage Sensor: 1:10 (Scale 110)
  • No Current Sensor built-in, supports external current sensor of PDB/4in1


  • INAV target: MATEKF722mini
  • BetaFlight unified target: MATEKF722mini(MTKS)
  • BetaFlight legacy target: MATEKF722SE


  • Mounting
    • 20 x 20mm/Φ3mm with Silicon Grommets
    • 20 x 20mm/Φ2mm with Silicon & Brass Grommets
    • 30.5 x 30.5mm/Φ3mm with Conversion Plate and Silicon Grommets
  • Dimensions:  28 x 28 mm
  • Weight: 5g


  • 1x FC F722-miniSE
  • 1x 20mm to 30.5mm conversion plate
  • 6x Silicon grommets M4 to M3
  • 6x Brass grommets M3 to M2
  • 1x SH1.0_8pin cable 5cm
  • 2x SH1.0_8pin connectors


Matek F722-mini(SE)
Matek F722-mini(SE)























































Pad/Hole Pin name Function BetaFlight INav INav INav
Multirotor Multirotor Tricopter Plane
S1 PB4 TIM3_CH1 motor-1 motor-1 motor-1 servo
S2 PB5 TIM3_CH2 motor-2 motor-2 motor-2 servo
S3 PB0 TIM3_CH3 motor-3 motor-3 motor-3 servo
S4 PB1 TIM3_CH4 motor-4 motor-4 servo
S5 PA15 TIM2_CH1 motor-5 motor-5 servo
S6 PB3 TIM2_CH2 motor-6 motor-6 servo
S7 PB6 TIM4_CH1 motor-7 servo servo motor-1
S8 PB7 TIM4_CH2 motor-8 servo motor-2
LED PA8 TIM1_CH1 2812LED 2812LED 2812LED 2812LED
RX2 PA3 TIM9_CH2 RX2/ppm RX2/ppm RX2/ppm RX2/ppm
TX2 PA2 TIM9_CH1 TX2/pwm1 TX2 TX2 TX2
RX4 PA1 TIM5_CH2 RX4/pwm2
TX4 PA0 TIM5_CH1 TX4/pwm3
PA4 PA4 ADC AirSpeed


  • INAV2.5.1 and Betaflight 2.4.x downloaded from configurator don’t support new barometer DPS310.
  • DPS310 will be supported officially by INAV2.6/ BetaFlight 4.3 and new configurator.
  • For now, pls download customized INAV2.5.1 and BetaFlight 2.4.0 from here.


If Baro can’t be detected. In INAV CLI mode, type command

  • set baro_hardware = DPS310
  • save


If Baro can’t be detected. In BF CLI mode, type command

  • set baro_bustype = I2C
  • set baro_i2c_device = 1
  • set baro_i2c_address = 118
  • set baro_hardware = DPS310
  • save



Additional information

Weight 5 g
Dimensions 5 × 5 × 0.25 cm


There are no reviews yet.

Be the first to review “MATEK FLIGHT CONTROLLER F722-MINI(SE)”