Speedybee Stack F7 V2 – 45A 4IN1 (32-BIT) ESC+WiFi & BLE+DJI JST Slot

The latest F7 flight controller  from Speedybee with built-in WiFi and Bluetooth for wireless firmware flashing, Betaflight/Speedybee App Configuration and full setup plus more! The beautiful new FC comes with an on-board DJI Air Unit JST connector for simple plug and play digital FPV, And gets paired with the new, top-of-the-line, 32-bit (BLHeli32) 45A (55A Burst) 4IN1 ESC!


  • MCU: STM32F722
  • IMU: MPU6000
  • USB: Type-C
  • Baro: BMP280 (I2C)
  • OSD: BetaFlight OSD w/ AT7456E chip
  • BLE: Support, used for Flight Controller configuration
  • WiFi: Support, used for data transfer, e.g firmware flashing, and Blackbox analysis.
  • DJI Air Unit slot: A full DJI Air Unit JST slot onboard
  • BlackBox: 16MB onboard dataflash
  • Current Sensor: 1 : 10 (Scale 168)
  • BetaFlight Camera Control Pad: Yes
  • Power input: 3S – 6S Lipo
  • 5V power output: 7 * 5V output, 6 pads and a BZ+ pad used for Buzzer, the maximum load current is 2.5A. 9V * 1, the maximum load current is 2.5A.
  • 9V power output: 2 * 9V output, 1 pads and another one used for DJI slot
  • 4.5V power output: 1 * 4.5V output pad
  • 3.3V power output: 1 * 3.3V output pad, the maximum load current is 500mA.
  • ESC signal: M1 – M4
  • UART: Full UART * 5(UART1, UART2, UART3, UART5, UART6)
  • ESC Telemetry UART: UART4 RX
  • I2C: Used for external Magnetometer, Sonar, etc.
  • LED pin: Used for WS2812 LED
  • Buzzer: BZ+ and BZ- pad used for 5V Buzzer
  • Boot button: Used to easy enter DFU mode
  • RSSI input: RSSI input solder pad
  • SmartPort: Use any TX pad of UART for the SmartPort feature.
  • Support Flight Controller Firmware: BetaFlight(Default), EMUFlight
  • Target name: SPEEDYBEEF7V2
  • Mounting: 30.5 x 30.5mm,  4mm hole size
  • Dimension: 41 x 38 x 6.9mm
  • Weight: 9g


  • Firmware: BLHeli32 SpeedyBee 4in1
  • MCU: STM32F051
  • Continuous Current: 45A * 4
  • Burst Current: 55A(10S)
  • ESC Protocol: DSHOT300/600/1200
  • Power input: 3S – 6S LiPo
  • Power output: VBAT
  • Current Sensor: Support (Scale 168)
  • ESC Telemetry: Support
  • Mounting: 30.5 x 30.5mm, 4mm hole size
  • Dimension: 41 * 45 * 6.5mm
  • Weight: 12.5g


  • 1x SpeedyBee F7 V2 FC
  • 1x SpeedyBee 45A ESC
  • 1x 50V 470uF Capacitor
  • 1x XT60 Cable
  • 1x JST 8pin 30mm
  • 1x JST 8pin 15mm
  • 1x DJI 6pin 80mm
  • 5x M3*30 screws
  • 5x Nylon Nuts
  • 5x Grommets M3*8mm
  • 5x Grommets M3*6.6mm


SpeedyBee F7 V2 30x30 3-6S Stack for DJI for Sale